GE EPM 5300 Manual do Utilizador Página 93
- Página / 100
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
CHAPTER 15: PROGRAMMING QUICK REFERENCE
GE Multilin EPM 5000 series Advanced Power Meters 89
8P2. Power Uni/Bi Directional Selection
A. Port 4
B. Port 5
C. Port 6
D. Port 7
8P3. Power Uni/Bi Directional Selection
A. Port 8
B. Port 9
C. Reserved
D. Reserved
80. DC output Port 0
80F. Parameter Mapping
80L. Low-End Calibration
80H. High-End Calibration
81. DC output Port 1
81F. Parameter Mapping
81L. Low-End Calibration
81H. High-End Calibration
89. DC output Port 9
89F. Parameter Mapping
89L. Low-End Calibration
89H. High-End Calibration
KEY DESIGNATIONS
MAX/MIN/LIMITS Scroll Groups
Scroll Functions
VOLTS Scroll Packs
A
MP
S
Enter/Exit Group
Enter/Exit
- Instruction Manual 1
- TABLE OF CONTENTS 3
- CHAPTER 1 5
- AC POWER MEASUREMENT 5
- 1.2: Three-Phase System 6
- 1) Delta 7
- 1.4: Waveform and Harmonics 8
- % THD GRAPH 8
- CHAPTER 2 9
- MECHANICAL INSTALLATION 9
- BACK VIEW 10
- CHAPTER 3 11
- ELECTRICAL INSTALLATION 11
- LIST OF CONNECTION DIAGRAMS 13
- EPM 5300P RELAY OVERVIEW 18
- CONNECTION FOR DB-9 FEMALE 21
- 5300P Instruments (rear view) 22
- Communications Port 23
- Model #SF485DB 23
- UNICOM 2500 24
- (Bottom View Shown) 24
- Model#SF485DB 25
- COMPUTER 27
- CHAPTER 5 31
- OVERVIEW 31
- AC VOLTS 32
- 5.6: Resetting Values 34
- UNPROTECTED RESET 35
- PROTECTED RESET 35
- 5.7: Resetting Hour Readings 36
- 5.10: Access Modes 38
- 5.11 Print Operating Data 38
- 5.12: Print Programming Data 39
- CHAPTER 6 41
- PROGRAMMING OVERVIEW 41
- SED FOR PROGRAMMING 42
- ASSWORD ENTRY 42
- CHAPTER 7 43
- EPM 5200P 43
- CHAPTER 8 45
- ENTERING PROGRAMMING MODE 45
- CHAPTER 9 47
- FUNCTION 50
- 9.5 Modbus Plus Capability 52
- PRINTING OPTION 52
- 9.7: Relay Mode 54
- DEFINITIONS: 54
- PROGRAMMING STEPS: 55
- CHAPTER 10 63
- SETTINGS 63
- VOLTAGE FULL SCALE: 64
- NTERING THE SCALE FACTOR: 65
- ECIMAL POINT SELECTION: 65
- YPE FULL SCALE 66
- CHAPTER 11 71
- CHAPTER 12 75
- AC AM PS 76
- RELAY 2 77
- SPECIAL CASES 78
- UNCTION 79
- Over/Under %THD Conditions 80
- 13.2: Trip Relay 83
- CHAPTER 14 87
- EXITING PROGRAMMING MODE 87
- CHAPTER 15 89
- PROGRAMMING QUICK REFERENCE 89
- 15.6: Group 2: Calibration 91
- 15.10: Group 6: THD Limits 92
- KEY DESIGNATIONS 93
- CHAPTER 16 95
- ETHERNET OPTION 95
- 16.2: Ethernet Option Setup 96
- 16.3: Default IP Address 97
- 16.4: AutoIP 97
- 16.5: Setting the IP Address 97
- 16.6: Network Configuration 98
- Multilin 100
Manuais e produtos relacionados com Medição, teste e controlo GE EPM 5300
(68 páginas)Gasboy Hardware uživatelské příručky
Začínající na T
Comentários a estes Manuais