GE E2SA Guia de Instalação descarregar pdf (Página 2)

3c. PHOTOELECTRIC CONTROL

• When used, photoelectric (PE) receptacle should be

oriented so that the word “North” is directed toward

true north.

• Seat the PE control in the receptacle, Lift and rotate them

clockwise until word “North” is directed toward true north.

• Lower the PE control and receptacle to ﬁrmly seat them

into position.

• Alternatively, PE receptacle can be oriented by lifting up on

rim of the PE receptacle and rotating it until the word

“North” is directed toward true north.

• Lower PE receptacle to ﬁrmly seat it in this position.

Then install PE control.

MOUNTING

3a. PRE-INSTALLATION

The E2SA luminaire unit pack mounts on a round wood

pole. Install the mounting arm ﬁrst. Drill a clearance

hole for a 5/8-inch diameter bolt through the pole. Insert

the 10-inch bolt through pole and loosely fasten with

the 2-inch square washer and nut. Hook the arm’s

pole plate on the bolt head in the upper slot of the

arm plate. (See Figure 1)

3b. INSTALLATION

Tighten nut to secure mounting arm to pole. Insert lag

bolts in outer lower holes of mounting arm. Hammer

in lag bolts to approximately 1” of head then tighten

with wrench. Insert leads in arm entering at outboard

end and exiting at end adjacent to pole plate. Create a

drip loop with leads as shown.

Slipﬁtter clamp is factory installed for a 1 1/4 inch pipe.

If using a 2” pipe remove, invert, and refasten the

slipﬁtter clamp to the housing. Open ﬁxture mounting

slipﬁtter clamp enough to insert mounting arm. Slide

ﬁxture onto arm until resting on pipe stop. Lightly

tighten slipﬁtter bolts. Level housing front-to-back using

steps on pipe stop and right-to-left by twisting housing

on pipe. Tighten clamp bolts to 10-15 foot-pounds.

WARNING

Risk of injury or damage. Unit will fall if not installed

properly. Follow installation instructions.

Top Housing Assy

LE W/O Refractor

LE W/ Refractor

Arm

Lag Bolts

Nuts

Square Washer

Thru Bolt

Figure 1

Figure 2

HANDLING

• This luminaire has been properly packed so that no

parts should have been damaged during transit.

• Inspect to conﬁrm.

• Damage may occur if luminaire is improperly handled

outside of pack.

• Do not impact or stack luminaire after removal from

packaging.

UNPACKING

1 2 3 4 5 6 7 ... 11 12

Comentários a estes Manuais

Sem comentários

Models	Document Type
02157	User Manual Revell 02157, 36 pages
02158	User Manual Revell 02158, 36 pages
02165	User Manual Revell 02165, 11 pages
04800	User Manual Revell 04800, 16 pages
04882	User Manual Revell 04882, 24 pages
05408	User Manual Revell H.M.S. Victory, 12 pages
05412	User Manual Revell 05412, 8 pages
05605	Manual Revell 05605, 28 pages
05715	User Manual Revell 05715, 20 pages
05758	User Manual Revell 05758, 12 pages
07005	Manual Revell 07005, 11 pages
07070	Manual Revell 07070, 12 pages
07072	User Manual Revell 07072, 18 pages
07073	Manual Revell 07073, 18 pages
07078	User Manual Revell 07078, 16 pages
07399	User Manual Revell 07399, 14 pages
B-25J Mitchell	Manual Revell B-25J Mitchell, 11 pages
EC135 ADAC	User Manual Revell EC135 ADAC, 16 pages
F4U-4 Corsair	Manual Revell F4U-4 Corsair, 8 pages
Millennium Falcon	User Manual Revell Millennium Falcon, 6 pages
U.S.S. VOYAGER	User Manual Revell U.S.S. VOYAGER, 16 pages

GE E2SA Guia de Instalação Página 2

Comentários a estes Manuais

Revell Toy models user manuals

GE E2SA Guia de Instalação Página 2

Comentários a estes Manuais

Manuais e produtos relacionados com não GE E2SA

Revell Toy models user manuals