Ge HC HP Manual do Utilizador descarregar pdf (Página 10)

GE MDS Intrepid-HC HP Installation Guide

1-4

1+0/1+1 Installation

This section describes the installation procedure for GE MDS Intrepid-HC HP in a 1+0 or 1+1 configuration.

The components involved in this procedure include the following:

 RFU

 OCB

 Hanger Kit

 Pole Mount Kit

Assembling the RFU and OCB

The RFU is generally assembled in the factory with the OCB, and delivered as a single unit.

If the RFU is delivered separately with the OCB, do the following:

Important:

The instructions in this guide should be performed indoors.

1. Remove the RFU and the OCB from the box.

2. Make sure that the OCB sealing gasket is in place.

OCB

RFU

Fil

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 113 114

Intrepid-HC HP 1
Table of Contents 3
CLASS 1 LASER PRODUCT 4
子信息品有毒有害物申明 5
Chapter 1: Installation 7
GE MDS Intrepid-HC HP RFU 8
1+0/1+1 Installation 10
Assembling the Hanger Kit 12
Four Screws 13
Fastening the 13
Pole Mount Kit 13
RFU Cable Connections 17
2+2 XPIC Installation 18
Installation Components 19
Installation Procedure 19
N+1 Split Mount Installation 22
1+0 Configuration 25
1+0 SD Configuration 25
1+1 HSB Configuration 26
1+1 SD Configuration 26
1+1 FD Configuration 27
1+1 FD/SD Configuration 27
1+1 SD BBS Configuration 28
2+0 DP Configuration 29
2+0 SD DP Configuration 29
2+0 SP Configuration 30
2+0 SD SP Configuration 30
2+2 Hot Standby Dual Pole 31
2+2 HSB SP Configuration 32
2+2 SD DP Configuration 33
2+2 SD SP Configuration 34
2+2 FD SP Configuration 35
2+2 HSB FD DP Configuration 36
2+2 SD/FD DP Configuration 37
4+1 FD DP Configuration 38
5+1 FD DP Configuration 39
4+1 FD SD DP Configuration 40
5+1 FD SD DP Configuration 41
Defining IP Addresses 45
To define IP Addresses: 46
NMS PC Requirements 47
Starting the NMS 48
External Alarms Setup 54
Exiting the NMS 55
##*3 floorshelfIPbaseIP ++= 58
shelves. The subnet is not 59
Connecting Line Interfaces 74
Procedures 75
Site Acceptance Procedure 76
1+0 Commissioning Procedure 81
Management Verification 82
Loopback Operation 82
1+1 Commissioning Procedure 83
Switching Tests 84
XPIC Installation Guidelines 86
XPIC Commissioning Tests 87
XPIC Recovery Verification 88
2+2 Verification 88
3-15 89
3-17 91
Protection Connector Pin-Out 95
8 x E1/T1 Connector Pin-Out 95
E1/T1 Connector Pin-Out 97
10BaseT Connector Pin-Out 97
Configuring PPP 99
General 101
Frequency Channels 101
6H GHz (6.45-7.1 GHz) 104
7 GHz (7.1-7.9 GHz) 105
ITU-R 385-7 [0] 107
8 GHz (7.8-8.5 GHz) 111
IN CASE OF DIFFICULTY 113

Comentários a estes Manuais

Sem comentários

Ge HC HP Manual do Utilizador Página 10

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Ge HC HP